Building a Green Wall - Part 2

So in the last part 1 entry I'd created a quite significantly large and quite ugly looking black and blue wall. Well now in part 2 we're going to make it spectacularly beautiful!

The right hand large blanket added and setting up for the top middle

The greenwall blankets were dead easy to put up. In the photo above you can see the right hand blanket attached, and I'm setting up for the middle one. To attach it I first clamp the blanket to the top of the wall using quick-grip clamps so I can line up the blanket. You need to take care here to ensure that it's stretched tautly otherwise when you load it up with soil it will bow out from the wall.

Once clamped I then drilled a small pilot hole into each eyelet. Remember blue-board is effectively a sheet of concrete, so you need to use a masonry bit to get through it! I then finally drive in a 50mm hex-head screw with washer to secure the blanket to the wall, again making sure that everything is stretched nice and tight before finally tightening up all the screws.

For the large blanket there are 5 fittings across the top, 3 in the middle, and then 3 at the top of the bottom row, which all lined up with the 70x45 battens I had put in when making the frame.

Right and middle completed

Above shows the two middle medium blankets fixed in place in the centre panel. That leaves the large one on the left to be done next!

The large blanket

Above shows a closer view of the large blanket and it's really quite an ingenious design. The kit comes with drip feeder tubes and connections that slide into the fabric above each row of planter pockets. The water from the drippers soak the blanket (remembering it's rubber backed) which in turn waters the pockets. Very clever.

All blankets mounted

This shows the completion of putting up the blankets. Once they were finished I then painted over any of the blue that was still visible to give it a uniform look.

Nice job

Here's the view down the side of the yard. The next job is to fit on the Holman Greenwall planters at the bottom of the large blankets. There's 3 for each side, 6 in total, and luckily for me 3 of the units is pretty much the exact width of the large blanket! Anyone would think I'd planned it that way!

Mounting the planter pots

This shot shows the planter pots fitted on to the bottom under the large right hand blanket. To fit them you have to fix a mounting bracket to the wall that the unit then hangs from. Each unit then clicks into the next one like kids building blocks. For watering you just run a pipe in the bottom of one with a standard snap-on hose connector. If one unit is connected to water, they're all connected, and then there's then an individual dripper for each pot. Another clever design.

Build finished. Now onto the plants

Above is the completed wall with all the blankets and pots in and plumbed. I also added some 12v up and down lighting on either side of the middle section to highlight the plants at night. When everything is done I'll also hook some spots on the ground in front of each panel.

So all that is left now is to plant the plants! There's 44 needed for the large blankets, and 20 for the two medium blankets, and 48 for all the pots. That's 112 plants (and then some as I was to find out) to buy and plant, so I'd better get cracking!

Centre section planted

Above shows the completed and planted centre section. The wall faces due south and is pretty shaded for much of the day, so I picked some sun loving cascading plants for the top level, and then worked my way down the wall until I got down to very shade tolerant ferns at the bottom. I brought the plants in pairs so it would give the wall a nice even look. I also ended up buying more than 112 as some of the bigger pockets can accommodate two or three medium plants, just to give more variety.

The guys at Jamie Durie emailed me a planting guide on request which was pretty handy, but it was mostly for a Sydney climate, not a Melbourne one. So I took it down to the local nursery at Bulleen Art and Garden who helped me pick the kinds of species from the list that I should be planting. 

After the first section it was pretty easy, I just used a good quality general purpose potting mix to fill the pockets to plant into.

Starting to plant the right side

Above you can see I am getting ready to plant out one of the large blankets. For the bottom row small pots I just bought a few trays of Petunia and Impatiens which were super cheap, and allowed me to plant all the pots. I also spot planted the leftover ones randomly in amongst the bigger plants to give that burst of colour in all the green.

For the placement of the bigger plants, as you can see in the picture, I would just drop the whole pot (or pots) into the pockets to see how it would look when planted. The big pockets can hold a large pot or two medium pots. Doing this first allows you to mix and move things about before taking the plunge and planting the plants permanently.

Once I was satisfied with the look I'd then start at the top row and half fill the pocket with potting mix, then de-pot and drop the plant in, and finally fill in around the plant with more mix. When it was filled I'd then give the pocket a bit of a bash with my fist just to settle the soil and plant in, water it in well, and then move onto the next pocket.

Planting done

Pretty soon the whole wall was done! In terms of costs it was around $600 - $700 per panel to plant them out, but the final product was worth every cent! I'm really happy with the result.

Job done. Time for a beer

This is now my number one favourite spot, and thanks to the beautiful new green wall we have some privacy while still being able to say hi to the neighbours, and we're doing the planet a favour to boot! 

With the trailing plants on the top row I have begun training some of them to go over the back of the wall as well, so that it will eventually soften the look on the other side too.

The lunch table is set and the BBQ is on!

So that's it for the green wall project, I hope you enjoyed the journey as much as I enjoy the result on an almost daily basis. Until next time, stay green!

Deck Building. Landscaping Around the Deck

So the deck is done at last, at least in terms of construction, now it just needs to "fit" in the back yard. Right back when I started laying the yard out I always had a vision of some kind of stairway to take me up from the paved area and onto the deck. However the other staircase I built already suited that purpose, and I really didn't want two sets of identical stairs off the same deck.

I needed some inspiration to go between the white lines!

Basic steps. What to do?

On a visit to Japan we went to Ōkōchi Sansō (大河内山荘 Ōkōchi Sansō, literally "Okochi Mountain Villa") which is the former home and garden of the Japanese period film actor Denjirō Ōkōchi, and is located on the edge of the famous bamboo forests of Arashiyama in Kyoto. This gorgeous garden is open to the public (for a fee) and served as inspiration for what I decided to do with the alternate path.

Below shows a great example of a path that leads up through the garden. The stepping stones are made from large pieces of local stone, and assembled in such a way that they look part of the natural landscape, but still indicate the path to follow.

A natural rock path disappearing around the corner

Periodically along the path you come across these gravelled areas as you can see below, set to resemble flowing water coming down the hillside.

A beautifully landscaped gravel path

From these gravelled areas the path then leads further along, using the natural stone as steps meandering up the side of the hill and throughout the garden.

The mysterious path continues upwards, one way

So using these photos for inspiration I called my favourite landscaper Stefan from Stefan's Landscape Design to have a look at what he could achieve. As always he looked at the photographs and understood exactly what I was after, and set about doing it.

The brief was to build a natural looking rocky outcrop with a stone path snaking up through it, containing a number of gravel landings linking the path to each switchback up the slope.

Two days later with a pile of rocks and a bobcat he achieved exactly what I was after! You can see below the landscaping prior to me enclosing the deck around it.

Now that the landscaping is complete I can enclose the last part of the decking

Once enclosed, the decking was now complete. From the circular paved area at the bottom the path goes up three stone steps to the right to a gravel landing, then switches back four steps to the left to the next landing, and then finally takes three more steps up to the right to meet just below the bottom of the decking, leaving one step up to the deck proper. He'd nailed it completely!

The landscaping and decking completed

He'd also included an extra gravel landing at the top as a lookout across the yard as you can see below with the gravel area to the right shown below.

The steps blend in faultlessly with the decking

Below shows the completed deck and garden area nicely planted with some ferns, mondo and dwarf pine shrubs.

The decking now landscaped in with the rest of the yard

The alternate path is now complete with easy access from the circular paved area up to the deck proper, but not in a obvious staircase manner. Call it a secret short cut if you like, because for all intents and purposes it just looks like a rock garden, but once you recognise the path, it draws you upward (or downward) to explore the trail.

The circular paved area is now linked to the decking via the rockery path

Unfortunately one thing fell victim to the construction, that being the back lawn. The bobcat moving back and forth carrying the heavy rocks and soil destroyed what was left of it. Truth be told it was pretty much dead anyway. Ever since laying in the turf, regardless of it being a shade tolerant species, the large pine tree slowly and surely started a war on the grass by dropping pine detritus upon it every time the wind blew.

I guess if I went out every weekend with a blower I may have kept it alive a little longer, but by the time I realised what was going on, the lawn was dead with the exception of one small area that was free from the tree. The bobcat finished the job and killed the remainder. RIP lawn.

RIP back lawn. You were great while you lasted.

What to do? Should I plant another? It wasn't a prospect I looked forward to. A little investigation and I settled on the artificial option, which would never die, well at least not for 25 years or so.

I went to a few suppliers and finally settled on a company called Synturf that manufactures the product locally. It does cost about 3 times more than instant turf, but they do everything for you. They start by coming in and digging out the old turf; then constructing and compacting a base to put the turf on, and finally lay and settle the turf on top pinning it down into the base and loading it up with sand to hold it firm.

The product is called Everest, and has a brown fleck throughout the grass that gives it a very natural look. Admittedly when some of the detritus from the tree falls onto the grass it looks more natural than ever! Everyone who sees it can't believe it's artificial grass, and it looks a million bucks as you can see.

The new lush green lawn is believe it or not, made of plastic!

So lets now take a trip back in time and as you can see below, this is the very first photo I took of the yard not long after we moved in. How different it looks now compared to back then. I remember we had to plant my son's Totem Tennis he got for Christmas that year in amongst the weeds.

Mowing the yard then was a case of getting out and hacking away with a brush-cutter. Things have changed!

We've come a long way since the beginning and the very first photo

Now you can compare it directly to below which shows the (pretty much) completed back yard. What a difference!

The completed yard sure looks different to how it started!

The new Synturf looks sensational, and the yard is now pretty much completed.

The new artificial turf has come up trumps

Below the deck is now ready for summer with many BBQ's to come.

All set and ready for summer BBQ's

Next time we'll apply a finish to the deck to complete the project.

Deck Building. Finishing the Flight of Stairs

One of the most popular posts I ever put up was building the frame for the flight of stairs that runs from the decking down to the lawn area. Well now that the top decking has been completed, it's time to deck the stairs. We're getting close and the end is in now sight. The last piece of this grand puzzle to be completed is literally a puzzle!

As I've gone to so much effort to deck everything, I wasn't prepared to leave any of that treated pine from the stair stringers showing. Adding to the complexity however is the whole "nail free" concept. The Deck Master system wasn't going to be much use on the steps as the treads are only three boards across, and to top it off I had run out of the Deck Master slotted timber! 

So the plan I came up with was to use the wood plugs which I thought (at the time!) would be less fiddly. Rather than use the Deck-Max plugs though as I was going to need hundreds of these things, I decided to make my own to save some money! 

I sniffed around online and came up with a vendor in Sydney called "The Wood Works" that sells a plug cutter and counterbore set. This consists of two drill bits in the set; one for cutting the 10mm wood plugs, and the other to counterbore the 10mm holes that the wood plugs fit into. Sounds simple.

Image courtesy "The Wood Works"

To use the plug cutter you need a drill press (or a plunge router) to hold the cutting bit perfectly vertical so that the plug comes out straight. Be prepared for this as it's a bit of a chore! 

It's a 4 step process:

1. Turn on the drill and place the timber
2. Slowly drop the drill press to cut the plug and then raise it once the cut is finished
3. Turn off the drill press
4. Using a small screwdriver, knock out the plug from the centre of the drill bit

Go back to step 1, and repeat 850 times! I had plenty of scrap off-cuts to work with from which the plugs are cut. 

Eventually you'll end up with a bag full of wooden plugs, but it doesn't stop there. To make the 10mm plugs easier to fit into the 10mm holes, you have the chamfer them on one end with a sander. For this I taped up my fingers (or else the sander will eventually go through your fingernail as I found out) and loaded the sander in a vice. Phew, this is a lot of effort for a finish! Maybe it would have been easier to buy these, but where's the satisfaction in that?

Eventually I was ready to go. The plan was to start with the top edge of the outside stringers, then infill the treads and risers, and finally veneer the outside stringers to match and knit in with the horizontal boards on the front side of the deck. Just like a giant 3D jigsaw puzzle!

Below shows the beginning of setting the boards onto the top edge of the left hand stringer. They have to be lined up such that the boards on the risers and treads sit will sit flush when fitted, but also line up with the horizontal facing boards on the deck!

Bring on the mitre joins. Starting out with the first boards.

I'd first cut the board to fit, make sure everything lines up and is level, then glue the underside with "liquid nails" and clamp it in place. Next, using the 10mm counterbore tool I would drill the hole, then fix a decking screw into the hole, lastly when the piece is glued and screwed, I'd glue and bang in my pre-cut wood plugs. When it's all dried you then cut off the excess with a vibrating multi-tool and give it a sand to finish. No nails showing!

Below shows the progress down the left hand side which is about 3/4 complete.

Fair progress down the left hand side

Cut, fit, glue, clamp, drill, screw and plug, over and over. Eventually as shown below I reached the bottom of the left hand side. Like a jigsaw I found it very therapeutic and relaxing work!

Left had side completed

Once the left was completed, I moved across to the right hand side and finished it to match.

Right hand side completed

Now both sides were done I could start putting down the treads, and then finally and hopefully, walk down the stairs for the first time!

Looking at both sides

Once I had the outside edges of the two side stringers completed, I started on the top stair tread sizing up the boards and riser as you can see below. Measure twice, cut once!

Sizing up the boards for the first step

Below shows the first step and riser completed and fixed in place and I can finally stand on the top step! Note the notch I had to cut into the rise on the centre stringer.

First step boards fixed down

The notch on the nose of the centre stringer is to accommodate the step lighting. I'm using the same lights to match the landing steps, with four of them to fit, one on every 2nd step.

Cutting the centre stringer to allow for the step light

Fitting the lights was easier than on the landing, as here I only had to deal with a single board whereas on the landing I had to fit the light in between two boards. 

Essentially I just found the centre of the board, marked out the square where the light will fit, then cut it out with a drill and jigsaw.

Sizing up the boards with the step light fitted

So three steps down with the first light fitted and it's looking pretty good. The extra effort in making sure the stringers were spot on when I was building the frame has paid off as everything is dead level.

Top 3 steps done

Below shows fitting the riser board in to make sure the gaps are uniform. I had some thin timber offcuts that I used to wedge around the board, and then used a large flat blade screwdriver to level it all in place nice and square. Finally I then drill the holes for the screws and plugs.

Wedging up the riser board to make sure it's centred

So here is the completed stair with all the treads and riser boards in place. I left all the wiring tied and hanging just behind the holes so I can now fit the rest of the stair lights in.

Putting in the risers to finish up the bottom steps

Job done as you can see below, with all the lights fitted in. Now there's just a matter of plugging a few hundred holes!

Steps completed

With the steps and deck front now completed, I can start the jigsaw puzzle down the side of the steps. Starting at the top left of the stair I carefully measure and cut the timbers to fit around the top edge boards to give it a 'continuous' look. 

Then like any other piece it gets glued, clamped, screwed and plugged. Each piece of timber is a unique cut to suit that step, so there's no mass production here!

Commencing the jigsaw puzzle

Below is a closer look to how I cut, clamp and space each piece of timber to fit. Using the left over Deck-Max biscuits from building the side deck gives me a perfect 3mm gap. I then use the clamps to hold in place while I glued and screw. Once it's set I just prize out the biscuits with a pair of multi-grips, ready to use again on the next piece.

Next step

So here you can see I have finished the timber puzzle on the left side of the stairs all the way to the bottom. 

Left hand side done

It's a bit of effort to go through to cut and round off each piece of unique timber, but I think it looks so much nicer than bare treated pine. Below is the right hand side plugged and polished.

The right hand side puzzle completed

Below shows the deck step lights on and working. They really give it a nice professional finish, and they're also very practical on a dark night!

Light it up!

So here is the deck showing both sets of stairs completed (well almost completed, there's still the matter of plugging a couple of hundred holes).

Stairs completed

So that's it, job done, steps completed. I can tell you I've walked up and down them many times now, and they work as designed. There's not an ounce of bounce! Rock solid baby.

Worth the effort

So now the deck construction is completed! Time for a well earned beer. 

Next post we'll look at landscaping around the deck to incorporate it into the rest of the yard, as well as cleaning and applying a finish.

Finishing up the Landing Steps

Happy New Year 2016 everyone!

I've been having a bit of a break enjoying the Australian Christmas summer time out on the back deck (asleep on the lounge some of the time too). 

Last post we laid the decking around the curved stonework, so now let's get back into it and look at finishing up of the landing steps by putting the boards down!

I decided to start simple and tackle the side steps first. Below you can see I start by fixing the nose board first, using the riser boards clamped underneath to make sure it all lines up. I then fixed the nose board down using the DeckMax counter-bore tool with screws and wood plugs.

The boards for the risers were a little trickier as I had to:

1. rip them down to size, allowing for a 3 mm gap above and below each board. You can see below I used slivers of offcuts to space the boards to 3 mm; and then
2. cut a hole in the middle for step lighting I wanted to fit (see the next picture below)

Fitting the nose board

The step light shown below is what I want to fit into the riser boards for all the steps. It took me a while to find exactly what I was looking for, and eventually had to import them from Hinkley Lighting in the USA via Amazon, as I couldn't find anything locally that was similar. They have a really comprehensive array of deck lighting available. 

They were pretty easy to fit, I just measured up the back of them and marked up the boards with the outline, then cut each board using the jigsaw.

Hinkley Lighting 1546BZ horizontal deck light (image courtesy of Amazon)

For the tread boards I had to cut in notches to the final board to fit around the stringers. I just measured them up, transposed them onto the board with a pencil, and then made the required cuts into the board with a jigsaw. Below you can see the bottom step completed with the light fitted in.

Bottom step completed with step light fitted

It's then just a case of replicating the process for the next set of boards for the facing riser and fitting it all together. Below is the completed side step with the lights in and turned on!

Side steps completed with operational stair lights

Having satisfied myself that it worked, I then moved on to the front step using the same methodology. In this instance though just to complicate things a little, there were mitre joins needed on each corner. 

I pre-cut all the boards before hand and clamped everything in place first just to make sure it was all going to fit. You'll notice I still use the Deck-Max "original" biscuits as spacers on the tread boards, as they are really great for getting the gap to exactly 3 mm, and I still have 1/2 a box left over from doing the side deck!

With the mitre joins I measured and cut the boards slightly over sized, and then using the circular saw proceeded to cut the smallest 1 mm or so "nibble" of the end, and tried it for size. If it didn't fit I'd take another mm off, and try again, and then again, until it was an exact fit. 

It's real easy to cut the wood shorter slowly, but it's damned hard to try and add it back on if you cut it too short, so take your time! 

You can see below I have already fixed the nose board, and have clamped up the next ones for size and spacing.

Checking the boards for size and spacing

Below shows the tread boards fitted and fixed. Like with the side step, I had to cut notches into the last board to fit around the stair stringers.

Step tread boards completed

As you can see below, it's worth taking the time on those mitre joins to get them spot on. The joins are all under cover, so I didn't have to worry too much about leaving a gap on the mitre. If this join was exposed to the weather you'd want to leave a mm or two gap on the mitre join to allow for any swelling of the wood that could occur.

Nice and precise joins make it a professional looking job

Below shows the finished step tread boards from the opposite angle. Once the glue on the wood plugs has dried you just cut them off with a vibrating multi-tool and sand them smooth.

Once small step for me, and giant leap in step building experience!

So once the tread boards were laid, as per the side step, I then ripped down the boards to go on the riser (to the same size), measured up, cut the holes for the step lights, and then fixed it all in. 

Below is the finished job.

The finished job

At last we can now walk out the back door without having to jump over anything! 

I could even sit on the back step and have a well deserved cold one.

Looking good

Below shows the deck landing with it's final coat of finish applied, and it really looks the goods, and quite professional in my own humble opinion! Well the wife is impressed too, and that's all that matters in the end really! A satisfied customer.

Not a bad job for an IT guy with some patience and power tools.

Adding the polish makes it come up a treat

Below is the step lighting fitted in and operational. I am really pleased with the look, and it was well worth the extra effort and expense to find the right lights.

The in-step lighting was worth all the trouble of importing the lights

Next post we are going to finish off the decking boards on the main deck, so until next time, happy new year for 2016 and chat soon.